英文字典中文字典


英文字典中文字典51ZiDian.com



中文字典辞典   英文字典 a   b   c   d   e   f   g   h   i   j   k   l   m   n   o   p   q   r   s   t   u   v   w   x   y   z       







请输入英文单字，中文词皆可：

alluvial    音标拼音: [,æl'uviəl]
a. 冲积的

冲积的

alluvial
adj 1: of or relating to alluvium


请选择你想看的字典辞典：
单词字典翻译
alluvial查看　alluvial　在百度字典中的解释百度英翻中〔查看〕
alluvial查看　alluvial　在Google字典中的解释Google英翻中〔查看〕
alluvial查看　alluvial　在Yahoo字典中的解释Yahoo英翻中〔查看〕

安装中文字典英文字典查询工具!


中文字典英文字典工具:
选择颜色:
输入中英文单字

































































英文字典中文字典相关资料:


  • Tapping for 10-32 - The Hobby-Machinist
    A #21 drill is what is recommended for 10-32 and that only 0 0027" bigger than 5 32" I'd recommenced a good spiral point H3 class tap before a new drill
  • Tap drill size for 1 2 -10 Acme | The Hobby-Machinist
    to calculate tap drill size for acme taps the magic formula step 1 1 Divided by TPI ( threads per inch) step 2 subtract this amount from the OD for pitches 10 and greater always add 005" for the drill size for pitches less than 10 TPI take the amount from step 1 and multiply x 05 ( 5 %) and add this to the drill size This is for 95% to 100
  • Clearance Drill For 10-32 - The Hobby-Machinist
    I use a lot of 10-32 screws The diameter of this size screw is published as 0 190 nominally, Although some seem smaller Based on this nominal diameter they will not fit through a 3 16 (0 188) hole What diameter do you use to drill clearance holes for these? Is there a metric size that works
  • Tapping for 10-32 | Page 2 | The Hobby-Machinist
    3 16" is approximately the major diameter of a #10 machine screw A 10-32 tap would barely scratch it, even if it drilled perfectly on size Hmm, 1 32nd would make that much a difference? Sorry for leading you the wrong way My mistake
  • Drill size for m10x1. 25? | The Hobby-Machinist
    Hi, I am making some new tierods for my atv, and need to know what size drill bit to use for an M10x1 25 tap My research shows 11 32 I just want to
  • Tap and Clearance Drill Sizes-Clarification Needed
    Machine screw size, or stub size There is latitude in what tap drill you use Smaller drills will make for more complete threads, which are stronger, but less so than you might think, and will put more strain on the tap Larger drills leave a somewhat weaker result, though again, less than you might think, and much less likely to break a tap
  • What Size Rod To What Size Die - The Hobby-Machinist
    if you wanted to cut a screw in 10-32 tpi you'd start with rod larger than 200" if you wanted to make a nut in 10- 32 you'd need to drill a hole 150" in diameter and then run a 10-32 tap in the hole
  • Stripped threads re-threading size questions - The Hobby-Machinist
    1 New thread diameter and pitch to source new bolts and taps 2 New tap pilot drill bit size that will create a smooth wall out of the stripped threads 3 Clearance fit drill size that the new bolts will comfortably fit through SAE or Metric are both fine, the correct size and being able to find quality bolts, drills, and taps are what is
  • What diameter rod to start with, for a given sized thread die?
    An 0-80 screw is (theoreticaly) 0 060 minus the thread pitch of 1 80, 0 0125", or 0 0475 (practicaly 0 048)" inch then becomes the tap drill for that size Thread pitch is a convenient source of calibration screws Many lathes have 10TPI lead screws, giving 0 100 per revolution A 20 pitch lead screw gives 0 050 per rev
  • Looking for a decent Tap Die set | Page 2 | The Hobby-Machinist
    @Ken - what are these sizes? Not familiar with these designations 6 - 40 Tap, #33 Drill; 8 - 36 Tap, #29 Drill; 10 - 24 Tap, #25 Drill; 10 - 32 Tap, #21 Drill;





中文字典-英文字典  2005-2009